/* $FreeBSD: head/sys/dev/usb/quirk/usb_quirk.h 326255 2017-11-27 14:52:40Z pfg $ */ /*- * SPDX-License-Identifier: BSD-2-Clause-FreeBSD * * Copyright (c) 2008 Hans Petter Selasky. All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. */ #ifndef _USB_QUIRK_H_ #define _USB_QUIRK_H_ enum { /* * Keep in sync with usb_quirk_str in usb_quirk.c, and with * share/man/man4/usb_quirk.4 */ UQ_NONE, /* not a valid quirk */ UQ_MATCH_VENDOR_ONLY, /* match quirk on vendor only */ /* Various quirks */ UQ_AUDIO_SWAP_LR, /* left and right sound channels are swapped */ UQ_AU_INP_ASYNC, /* input is async despite claim of adaptive */ UQ_AU_NO_FRAC, /* don't adjust for fractional samples */ UQ_AU_NO_XU, /* audio device has broken extension unit */ UQ_BAD_ADC, /* bad audio spec version number */ UQ_BAD_AUDIO, /* device claims audio class, but isn't */ UQ_BROKEN_BIDIR, /* printer has broken bidir mode */ UQ_BUS_POWERED, /* device is bus powered, despite claim */ UQ_HID_IGNORE, /* device should be ignored by hid class */ UQ_KBD_IGNORE, /* device should be ignored by kbd class */ UQ_KBD_BOOTPROTO, /* device should set the boot protocol */ UQ_KBD_DELAY_INIT, /* add short delay during initialization */ UQ_KBD_DELAY_CTRL_MSG, /* add short delay after sending ctl msg */ UQ_UMS_IGNORE, /* device should be ignored by ums class */ UQ_MS_BAD_CLASS, /* doesn't identify properly */ UQ_MS_LEADING_BYTE, /* mouse sends an unknown leading byte */ UQ_MS_REVZ, /* mouse has Z-axis reversed */ UQ_NO_STRINGS, /* string descriptors are broken */ UQ_POWER_CLAIM, /* hub lies about power status */ UQ_SPUR_BUT_UP, /* spurious mouse button up events */ UQ_SWAP_UNICODE, /* has some Unicode strings swapped */ UQ_CFG_INDEX_1, /* select configuration index 1 by default */ UQ_CFG_INDEX_2, /* select configuration index 2 by default */ UQ_CFG_INDEX_3, /* select configuration index 3 by default */ UQ_CFG_INDEX_4, /* select configuration index 4 by default */ UQ_CFG_INDEX_0, /* select configuration index 0 by default */ UQ_ASSUME_CM_OVER_DATA, /* assume cm over data feature */ /* * USB Mass Storage Quirks. See "storage/umass.c" for a * detailed description. */ UQ_MSC_NO_TEST_UNIT_READY, /* send start/stop instead of TUR */ UQ_MSC_NO_RS_CLEAR_UA, /* does not reset Unit Att. */ UQ_MSC_NO_START_STOP, /* does not support start/stop */ UQ_MSC_NO_GETMAXLUN, /* does not support get max LUN */ UQ_MSC_NO_INQUIRY, /* fake generic inq response */ UQ_MSC_NO_INQUIRY_EVPD, /* does not support inq EVPD */ UQ_MSC_NO_PREVENT_ALLOW, /* does not support medium removal */ UQ_MSC_NO_SYNC_CACHE, /* does not support sync cache */ UQ_MSC_SHUTTLE_INIT, /* requires Shuttle init sequence */ UQ_MSC_ALT_IFACE_1, /* switch to alternate interface 1 */ UQ_MSC_FLOPPY_SPEED, /* does floppy speeds (20kb/s) */ UQ_MSC_IGNORE_RESIDUE, /* gets residue wrong */ UQ_MSC_WRONG_CSWSIG, /* uses wrong CSW signature */ UQ_MSC_RBC_PAD_TO_12, /* pad RBC requests to 12 bytes */ UQ_MSC_READ_CAP_OFFBY1, /* reports sector count, not max sec. */ UQ_MSC_FORCE_SHORT_INQ, /* does not support full inq. */ UQ_MSC_FORCE_WIRE_BBB, /* force BBB wire protocol */ UQ_MSC_FORCE_WIRE_CBI, /* force CBI wire protocol */ UQ_MSC_FORCE_WIRE_CBI_I, /* force CBI with int. wire protocol */ UQ_MSC_FORCE_PROTO_SCSI, /* force SCSI command protocol */ UQ_MSC_FORCE_PROTO_ATAPI, /* force ATAPI command protocol */ UQ_MSC_FORCE_PROTO_UFI, /* force UFI command protocol */ UQ_MSC_FORCE_PROTO_RBC, /* force RBC command protocol */ /* Ejection of mass storage (driver disk) */ UQ_MSC_EJECT_HUAWEI, /* ejects after Huawei USB command */ UQ_MSC_EJECT_SIERRA, /* ejects after Sierra USB command */ UQ_MSC_EJECT_SCSIEJECT, /* ejects after SCSI eject command */ UQ_MSC_EJECT_REZERO, /* ejects after SCSI rezero command */ UQ_MSC_EJECT_ZTESTOR, /* ejects after ZTE SCSI command */ UQ_MSC_EJECT_CMOTECH, /* ejects after C-motech SCSI cmd */ UQ_MSC_EJECT_WAIT, /* wait for the device to eject */ UQ_MSC_EJECT_SAEL_M460, /* ejects after Sael USB commands */ UQ_MSC_EJECT_HUAWEISCSI, /* ejects after Huawei SCSI command */ UQ_MSC_EJECT_HUAWEISCSI2, /* ejects after Huawei SCSI 2 command */ UQ_MSC_EJECT_TCT, /* ejects after TCT SCSI command */ UQ_BAD_MIDI, /* device claims MIDI class, but isn't */ UQ_AU_VENDOR_CLASS, /* audio device uses vendor and not audio class */ UQ_SINGLE_CMD_MIDI, /* at most one command per USB packet */ UQ_MSC_DYMO_EJECT, /* ejects Dymo MSC device */ UQ_AU_SET_SPDIF_CM6206, /* enable S/PDIF audio output */ UQ_WMT_IGNORE, /* device should be ignored by wmt driver */ USB_QUIRK_MAX }; uint8_t usb_test_quirk(const struct usb_attach_arg *uaa, uint16_t quirk); #endif /* _USB_QUIRK_H_ */