/* * Copyright (c) 2002 Myson Technology Inc. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions, and the following disclaimer, * without modification, immediately at the beginning of the file. * 2. The name of the author may not be used to endorse or promote products * derived from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * Written by: yen_cw@myson.com.tw available at: http://www.myson.com.tw/ * * $FreeBSD: src/sys/dev/my/if_myreg.h,v 1.1.2.2 2002/04/17 02:05:27 julian Exp $ * $DragonFly: src/sys/dev/netif/my/if_myreg.h,v 1.5 2005/11/28 17:13:43 dillon Exp $ * * Myson MTD80x register definitions. * */ #define MY_PAR0 0x0 /* physical address 0-3 */ #define MY_PAR1 0x04 /* physical address 4-5 */ #define MY_MAR0 0x08 /* multicast address 0-3 */ #define MY_MAR1 0x0C /* multicast address 4-7 */ #define MY_FAR0 0x10 /* flow-control address 0-3 */ #define MY_FAR1 0x14 /* flow-control address 4-5 */ #define MY_TCRRCR 0x18 /* receive & transmit configuration */ #define MY_BCR 0x1C /* bus command */ #define MY_TXPDR 0x20 /* transmit polling demand */ #define MY_RXPDR 0x24 /* receive polling demand */ #define MY_RXCWP 0x28 /* receive current word pointer */ #define MY_TXLBA 0x2C /* transmit list base address */ #define MY_RXLBA 0x30 /* receive list base address */ #define MY_ISR 0x34 /* interrupt status */ #define MY_IMR 0x38 /* interrupt mask */ #define MY_FTH 0x3C /* flow control high/low threshold */ #define MY_MANAGEMENT 0x40 /* bootrom/eeprom and mii management */ #define MY_TALLY 0x44 /* tally counters for crc and mpa */ #define MY_TSR 0x48 /* tally counter for transmit status */ #define MY_PHYBASE 0x4c /* * Receive Configuration Register */ #define MY_RXRUN 0x00008000 /* receive running status */ #define MY_EIEN 0x00004000 /* early interrupt enable */ #define MY_RFCEN 0x00002000 /* receive flow control packet enable */ #define MY_NDFA 0x00001000 /* not defined flow control address */ #define MY_RBLEN 0x00000800 /* receive burst length enable */ #define MY_RPBLE1 0x00000000 /* 1 word */ #define MY_RPBLE4 0x00000100 /* 4 words */ #define MY_RPBLE8 0x00000200 /* 8 words */ #define MY_RPBLE16 0x00000300 /* 16 words */ #define MY_RPBLE32 0x00000400 /* 32 words */ #define MY_RPBLE64 0x00000500 /* 64 words */ #define MY_RPBLE128 0x00000600 /* 128 words */ #define MY_RPBLE512 0x00000700 /* 512 words */ #define MY_PROM 0x000000080 /* promiscuous mode */ #define MY_AB 0x000000040 /* accept broadcast */ #define MY_AM 0x000000020 /* accept mutlicast */ #define MY_ARP 0x000000008 /* receive runt pkt */ #define MY_ALP 0x000000004 /* receive long pkt */ #define MY_SEP 0x000000002 /* receive error pkt */ #define MY_RE 0x000000001 /* receive enable */ /* * Transmit Configuration Register */ #define MY_TXRUN 0x04000000 /* transmit running status */ #define MY_Enhanced 0x02000000 /* transmit enhanced mode */ #define MY_TFCEN 0x01000000 /* tx flow control packet enable */ #define MY_TFT64 0x00000000 /* 64 bytes */ #define MY_TFT32 0x00200000 /* 32 bytes */ #define MY_TFT128 0x00400000 /* 128 bytes */ #define MY_TFT256 0x00600000 /* 256 bytes */ #define MY_TFT512 0x00800000 /* 512 bytes */ #define MY_TFT768 0x00A00000 /* 768 bytes */ #define MY_TFT1024 0x00C00000 /* 1024 bytes */ #define MY_TFTSF 0x00E00000 /* store and forward */ #define MY_FD 0x00100000 /* full duplex mode */ #define MY_PS10 0x00080000 /* port speed is 10M */ #define MY_TE 0x00040000 /* transmit enable */ #define MY_PS1000 0x00010000 /* port speed is 1000M */ /* * Bus Command Register */ #define MY_PROG 0x00000200 /* programming */ #define MY_RLE 0x00000100 /* read line command enable */ #define MY_RME 0x00000080 /* read multiple command enable */ #define MY_WIE 0x00000040 /* write and invalidate cmd enable */ #define MY_PBL1 0x00000000 /* 1 dword */ #define MY_PBL4 0x00000008 /* 4 dwords */ #define MY_PBL8 0x00000010 /* 8 dwords */ #define MY_PBL16 0x00000018 /* 16 dwords */ #define MY_PBL32 0x00000020 /* 32 dwords */ #define MY_PBL64 0x00000028 /* 64 dwords */ #define MY_PBL128 0x00000030 /* 128 dwords */ #define MY_PBL512 0x00000038 /* 512 dwords */ #define MY_ABR 0x00000004 /* arbitration rule */ #define MY_BLS 0x00000002 /* big/little endian select */ #define MY_SWR 0x00000001 /* software reset */ /* * Transmit Poll Demand Register */ #define MY_TxPollDemand 0x1 /* * Receive Poll Demand Register */ #define MY_RxPollDemand 0x01 /* * Interrupt Status Register */ #define MY_RFCON 0x00020000 /* receive flow control xon packet */ #define MY_RFCOFF 0x00010000 /* receive flow control xoff packet */ #define MY_LSCStatus 0x00008000 /* link status change */ #define MY_ANCStatus 0x00004000 /* autonegotiation completed */ #define MY_FBE 0x00002000 /* fatal bus error */ #define MY_FBEMask 0x00001800 #define MY_ParityErr 0x00000000 /* parity error */ #define MY_MasterErr 0x00000800 /* master error */ #define MY_TargetErr 0x00001000 /* target abort */ #define MY_TUNF 0x00000400 /* transmit underflow */ #define MY_ROVF 0x00000200 /* receive overflow */ #define MY_ETI 0x00000100 /* transmit early int */ #define MY_ERI 0x00000080 /* receive early int */ #define MY_CNTOVF 0x00000040 /* counter overflow */ #define MY_RBU 0x00000020 /* receive buffer unavailable */ #define MY_TBU 0x00000010 /* transmit buffer unavilable */ #define MY_TI 0x00000008 /* transmit interrupt */ #define MY_RI 0x00000004 /* receive interrupt */ #define MY_RxErr 0x00000002 /* receive error */ /* * Interrupt Mask Register */ #define MY_MRFCON 0x00020000 /* receive flow control xon packet */ #define MY_MRFCOFF 0x00010000 /* receive flow control xoff packet */ #define MY_MLSCStatus 0x00008000 /* link status change */ #define MY_MANCStatus 0x00004000 /* autonegotiation completed */ #define MY_MFBE 0x00002000 /* fatal bus error */ #define MY_MFBEMask 0x00001800 #define MY_MTUNF 0x00000400 /* transmit underflow */ #define MY_MROVF 0x00000200 /* receive overflow */ #define MY_METI 0x00000100 /* transmit early int */ #define MY_MERI 0x00000080 /* receive early int */ #define MY_MCNTOVF 0x00000040 /* counter overflow */ #define MY_MRBU 0x00000020 /* receive buffer unavailable */ #define MY_MTBU 0x00000010 /* transmit buffer unavilable */ #define MY_MTI 0x00000008 /* transmit interrupt */ #define MY_MRI 0x00000004 /* receive interrupt */ #define MY_MRxErr 0x00000002 /* receive error */ /* 90/1/18 delete */ /* #define MY_INTRS MY_FBE|MY_MRBU|MY_TBU|MY_MTI|MY_MRI|MY_METI */ #define MY_INTRS MY_MRBU|MY_TBU|MY_MTI|MY_MRI|MY_METI /* * Flow Control High/Low Threshold Register */ #define MY_FCHTShift 16 /* flow control high threshold */ #define MY_FCLTShift 0 /* flow control low threshold */ /* * BootROM/EEPROM/MII Management Register */ #define MY_MASK_MIIR_MII_READ 0x00000000 #define MY_MASK_MIIR_MII_WRITE 0x00000008 #define MY_MASK_MIIR_MII_MDO 0x00000004 #define MY_MASK_MIIR_MII_MDI 0x00000002 #define MY_MASK_MIIR_MII_MDC 0x00000001 /* * Tally Counter for CRC and MPA */ #define MY_TCOVF 0x80000000 /* crc tally counter overflow */ #define MY_CRCMask 0x7fff0000 /* crc number: bit 16-30 */ #define MY_CRCShift 16 #define MY_TMOVF 0x00008000 /* mpa tally counter overflow */ #define MY_MPAMask 0x00007fff /* mpa number: bit 0-14 */ #define MY_MPAShift 0 /* * Tally Counters for transmit status */ #define MY_AbortMask 0xff000000 /* transmit abort number */ #define MY_AbortShift 24 #define MY_LColMask 0x00ff0000 /* transmit late collisions */ #define MY_LColShift 16 #define MY_NCRMask 0x0000ffff /* transmit retry number */ #define MY_NCRShift 0 /* * Myson TX/RX descriptor structure. */ struct my_desc { u_int32_t my_status; u_int32_t my_ctl; u_int32_t my_data; u_int32_t my_next; }; /* * for tx/rx descriptors */ #define MY_OWNByNIC 0x80000000 #define MY_OWNByDriver 0x0 /* * receive descriptor 0 */ #define MY_RXOWN 0x80000000 /* own bit */ #define MY_FLNGMASK 0x0fff0000 /* frame length */ #define MY_FLNGShift 16 #define MY_MARSTATUS 0x00004000 /* multicast address received */ #define MY_BARSTATUS 0x00002000 /* broadcast address received */ #define MY_PHYSTATUS 0x00001000 /* physical address received */ #define MY_RXFSD 0x00000800 /* first descriptor */ #define MY_RXLSD 0x00000400 /* last descriptor */ #define MY_ES 0x00000080 /* error summary */ #define MY_RUNT 0x00000040 /* runt packet received */ #define MY_LONG 0x00000020 /* long packet received */ #define MY_FAE 0x00000010 /* frame align error */ #define MY_CRC 0x00000008 /* crc error */ #define MY_RXER 0x00000004 /* receive error */ #define MY_RDES0CHECK 0x000078fc /* only check MAR, BAR, PHY, ES, RUNT, LONG, FAE, CRC and RXER bits */ /* * receive descriptor 1 */ #define MY_RXIC 0x00800000 /* interrupt control */ #define MY_RBSMASK 0x000007ff /* receive buffer size */ #define MY_RBSShift 0 /* * transmit descriptor 0 */ #define MY_TXERR 0x00008000 /* transmit error */ #define MY_JABTO 0x00004000 /* jabber timeout */ #define MY_CSL 0x00002000 /* carrier sense lost */ #define MY_LC 0x00001000 /* late collision */ #define MY_EC 0x00000800 /* excessive collision */ #define MY_UDF 0x00000400 /* fifo underflow */ #define MY_DFR 0x00000200 /* deferred */ #define MY_HF 0x00000100 /* heartbeat fail */ #define MY_NCRMASK 0x000000ff /* collision retry count */ #define MY_NCRShift 0 /* * tx descriptor 1 */ #define MY_TXIC 0x80000000 /* interrupt control */ #define MY_ETIControl 0x40000000 /* early transmit interrupt */ #define MY_TXLD 0x20000000 /* last descriptor */ #define MY_TXFD 0x10000000 /* first descriptor */ #define MY_CRCDisable 0x00000000 /* crc control */ #define MY_CRCEnable 0x08000000 #define MY_PADDisable 0x00000000 /* padding control */ #define MY_PADEnable 0x04000000 #define MY_RetryTxLC 0x02000000 /* retry late collision */ #define MY_PKTShift 11 /* transmit pkt size */ #define MY_TBSMASK 0x000007ff #define MY_TBSShift 0 /* transmit buffer size */ #define MY_MAXFRAGS 1 #define MY_RX_LIST_CNT 64 #define MY_TX_LIST_CNT 64 #define MY_MIN_FRAMELEN 60 /* * A transmit 'super descriptor' is actually MY_MAXFRAGS regular * descriptors clumped together. The idea here is to emulate the * multi-fragment descriptor layout found in devices such as the * Texas Instruments ThunderLAN and 3Com boomerang and cylone chips. * The advantage to using this scheme is that it avoids buffer copies. * The disadvantage is that there's a certain amount of overhead due * to the fact that each 'fragment' is 16 bytes long. In my tests, * this limits top speed to about 10.5MB/sec. It should be more like * 11.5MB/sec. However, the upshot is that you can achieve better * results on slower machines: a Pentium 200 can pump out packets at * same speed as a PII 400. */ struct my_txdesc { struct my_desc my_frag[MY_MAXFRAGS]; }; #define MY_TXSTATUS(x) x->my_ptr->my_frag[x->my_lastdesc].my_status #define MY_TXCTL(x) x->my_ptr->my_frag[x->my_lastdesc].my_ctl #define MY_TXDATA(x) x->my_ptr->my_frag[x->my_lastdesc].my_data #define MY_TXNEXT(x) x->my_ptr->my_frag[x->my_lastdesc].my_next #define MY_TXOWN(x) x->my_ptr->my_frag[0].my_status #define MY_UNSENT 0x1234 struct my_list_data { struct my_desc my_rx_list[MY_RX_LIST_CNT]; struct my_txdesc my_tx_list[MY_TX_LIST_CNT]; }; struct my_chain { struct my_txdesc *my_ptr; struct mbuf *my_mbuf; struct my_chain *my_nextdesc; u_int8_t my_lastdesc; }; struct my_chain_onefrag { struct my_desc *my_ptr; struct mbuf *my_mbuf; struct my_chain_onefrag *my_nextdesc; u_int8_t my_rlast; }; struct my_chain_data { struct my_chain_onefrag my_rx_chain[MY_RX_LIST_CNT]; struct my_chain my_tx_chain[MY_TX_LIST_CNT]; struct my_chain_onefrag *my_rx_head; struct my_chain *my_tx_head; struct my_chain *my_tx_tail; struct my_chain *my_tx_free; }; struct my_type { u_int16_t my_vid; u_int16_t my_did; char *my_name; }; #define MY_FLAG_FORCEDELAY 1 #define MY_FLAG_SCHEDDELAY 2 #define MY_FLAG_DELAYTIMEO 3 struct my_softc { struct arpcom arpcom; /* interface info */ struct ifmedia ifmedia; /* media info */ bus_space_handle_t my_bhandle; bus_space_tag_t my_btag; struct my_type *my_info; /* adapter info */ struct my_type *my_pinfo; /* phy info */ struct resource *my_res; struct resource *my_irq; void *my_intrhand; u_int8_t my_unit; /* interface number */ u_int8_t my_phy_addr; /* PHY address */ u_int8_t my_tx_pend; /* TX pending */ u_int8_t my_want_auto; u_int8_t my_autoneg; u_int16_t my_txthresh; u_int8_t my_stats_no_timeout; caddr_t my_ldata_ptr; struct my_list_data *my_ldata; struct my_chain_data my_cdata; device_t my_miibus; }; /* * register space access macros */ #define CSR_WRITE_4(sc, reg, val) \ bus_space_write_4(sc->my_btag, sc->my_bhandle, reg, val) #define CSR_WRITE_2(sc, reg, val) \ bus_space_write_2(sc->my_btag, sc->my_bhandle, reg, val) #define CSR_WRITE_1(sc, reg, val) \ bus_space_write_1(sc->my_btag, sc->my_bhandle, reg, val) #define CSR_READ_4(sc, reg) \ bus_space_read_4(sc->my_btag, sc->my_bhandle, reg) #define CSR_READ_2(sc, reg) \ bus_space_read_2(sc->my_btag, sc->my_bhandle, reg) #define CSR_READ_1(sc, reg) \ bus_space_read_1(sc->my_btag, sc->my_bhandle, reg) #define MY_TIMEOUT 1000 /* * General constants that are fun to know. * * MYSON PCI vendor ID */ #define MYSONVENDORID 0x1516 /* * MYSON device IDs. */ #define MTD800ID 0x0800 #define MTD803ID 0x0803 #define MTD891ID 0x0891 /* * ST+OP+PHYAD+REGAD+TA */ #define MY_OP_READ 0x6000 /* ST:01+OP:10+PHYAD+REGAD+TA:Z0 */ #define MY_OP_WRITE 0x5002 /* ST:01+OP:01+PHYAD+REGAD+TA:10 */ /* * Constansts for Myson PHY */ #define MysonPHYID0 0x0300 /* * Constansts for Seeq 80225 PHY */ #define SeeqPHYID0 0x0016 #define SEEQ_MIIRegister18 18 #define SEEQ_SPD_DET_100 0x80 #define SEEQ_DPLX_DET_FULL 0x40 /* * Constansts for Ahdoc 101 PHY */ #define AhdocPHYID0 0x0022 #define AHDOC_DiagnosticReg 18 #define AHDOC_DPLX_FULL 0x0800 #define AHDOC_Speed_100 0x0400 /* * Constansts for Marvell 88E1000/88E1000S PHY and LevelOne PHY */ #define MarvellPHYID0 0x0141 #define LevelOnePHYID0 0x0013 #define Marvell_SpecificStatus 17 #define Marvell_Speed1000 0x8000 #define Marvell_Speed100 0x4000 #define Marvell_FullDuplex 0x2000 /* * PCI low memory base and low I/O base register, and * other PCI registers. Note: some are only available on * the 3c905B, in particular those that related to power management. */ #define MY_PCI_VENDOR_ID 0x00 #define MY_PCI_DEVICE_ID 0x02 #define MY_PCI_COMMAND 0x04 #define MY_PCI_STATUS 0x06 #define MY_PCI_CLASSCODE 0x09 #define MY_PCI_LATENCY_TIMER 0x0D #define MY_PCI_HEADER_TYPE 0x0E #define MY_PCI_LOIO 0x10 #define MY_PCI_LOMEM 0x14 #define MY_PCI_BIOSROM 0x30 #define MY_PCI_INTLINE 0x3C #define MY_PCI_INTPIN 0x3D #define MY_PCI_MINGNT 0x3E #define MY_PCI_MINLAT 0x0F #define MY_PCI_RESETOPT 0x48 #define MY_PCI_EEPROM_DATA 0x4C #define PHY_UNKNOWN 3 #define MY_PHYADDR_MIN 0x00 #define MY_PHYADDR_MAX 0x1F #define PHY_BMCR 0x00 #define PHY_BMSR 0x01 #define PHY_VENID 0x02 #define PHY_DEVID 0x03 #define PHY_ANAR 0x04 #define PHY_LPAR 0x05 #define PHY_ANEXP 0x06 #define PHY_NPTR 0x07 #define PHY_LPNPR 0x08 #define PHY_1000CR 0x09 #define PHY_1000SR 0x0a #define PHY_ANAR_NEXTPAGE 0x8000 #define PHY_ANAR_RSVD0 0x4000 #define PHY_ANAR_TLRFLT 0x2000 #define PHY_ANAR_RSVD1 0x1000 #define PHY_ANAR_RSVD2 0x0800 #define PHY_ANAR_RSVD3 0x0400 #define PHY_ANAR_100BT4 0x0200L #define PHY_ANAR_100BTXFULL 0x0100 #define PHY_ANAR_100BTXHALF 0x0080 #define PHY_ANAR_10BTFULL 0x0040 #define PHY_ANAR_10BTHALF 0x0020 #define PHY_ANAR_PROTO4 0x0010 #define PHY_ANAR_PROTO3 0x0008 #define PHY_ANAR_PROTO2 0x0004 #define PHY_ANAR_PROTO1 0x0002 #define PHY_ANAR_PROTO0 0x0001 #define PHY_1000SR_1000BTXFULL 0x0800 #define PHY_1000SR_1000BTXHALF 0x0400 /* * These are the register definitions for the PHY (physical layer * interface chip). */ /* * PHY BMCR Basic Mode Control Register */ #define PHY_BMCR_RESET 0x8000 #define PHY_BMCR_LOOPBK 0x4000 #define PHY_BMCR_SPEEDSEL 0x2000 #define PHY_BMCR_AUTONEGENBL 0x1000 #define PHY_BMCR_RSVD0 0x0800 /* write as zero */ #define PHY_BMCR_ISOLATE 0x0400 #define PHY_BMCR_AUTONEGRSTR 0x0200 #define PHY_BMCR_DUPLEX 0x0100 #define PHY_BMCR_COLLTEST 0x0080 #define PHY_BMCR_1000 0x0040 /* only used for Marvell PHY */ #define PHY_BMCR_RSVD2 0x0020 /* write as zero, don't care */ #define PHY_BMCR_RSVD3 0x0010 /* write as zero, don't care */ #define PHY_BMCR_RSVD4 0x0008 /* write as zero, don't care */ #define PHY_BMCR_RSVD5 0x0004 /* write as zero, don't care */ #define PHY_BMCR_RSVD6 0x0002 /* write as zero, don't care */ #define PHY_BMCR_RSVD7 0x0001 /* write as zero, don't care */ /* * RESET: 1 == software reset, 0 == normal operation * Resets status and control registers to default values. * Relatches all hardware config values. * * LOOPBK: 1 == loopback operation enabled, 0 == normal operation * * SPEEDSEL: 1 == 100Mb/s, 0 == 10Mb/s * Link speed is selected byt his bit or if auto-negotiation if bit * 12 (AUTONEGENBL) is set (in which case the value of this register * is ignored). * * AUTONEGENBL: 1 == Autonegotiation enabled, 0 == Autonegotiation disabled * Bits 8 and 13 are ignored when autoneg is set, otherwise bits 8 and 13 * determine speed and mode. Should be cleared and then set if PHY configured * for no autoneg on startup. * * ISOLATE: 1 == isolate PHY from MII, 0 == normal operation * * AUTONEGRSTR: 1 == restart autonegotiation, 0 = normal operation * * DUPLEX: 1 == full duplex mode, 0 == half duplex mode * * COLLTEST: 1 == collision test enabled, 0 == normal operation */ /* * PHY, BMSR Basic Mode Status Register */ #define PHY_BMSR_100BT4 0x8000 #define PHY_BMSR_100BTXFULL 0x4000 #define PHY_BMSR_100BTXHALF 0x2000 #define PHY_BMSR_10BTFULL 0x1000 #define PHY_BMSR_10BTHALF 0x0800 #define PHY_BMSR_RSVD1 0x0400 /* write as zero, don't care */ #define PHY_BMSR_RSVD2 0x0200 /* write as zero, don't care */ #define PHY_BMSR_RSVD3 0x0100 /* write as zero, don't care */ #define PHY_BMSR_RSVD4 0x0080 /* write as zero, don't care */ #define PHY_BMSR_MFPRESUP 0x0040 #define PHY_BMSR_AUTONEGCOMP 0x0020 #define PHY_BMSR_REMFAULT 0x0010 #define PHY_BMSR_CANAUTONEG 0x0008 #define PHY_BMSR_LINKSTAT 0x0004 #define PHY_BMSR_JABBER 0x0002 #define PHY_BMSR_EXTENDED 0x0001